Brand name: DYS
Item Name: Aria F45A 4in1 ESC
Input voltage:3-5S Lipo
BEC: 5V/3A & 9V/1.5A
Size(mm)L*W*H:43*40*8(mm)
Weight:19.8g(without battery wire)
Cont Current(A):45A
Burts Current(A)>10S:50A

Features:
◆ With 32bit ARM Cortex MCU STM32F051 48MHZ micro processor, throttle 2048 resolution ratio,strong anti-interference capacity.
◆ Built-in two BEC 9V / 1.5A and 5V/ 3A.
◆ The telemetry port and on-board current meter of the ESC can use the flat cable and it will test the current,voltage and power etc.
◆Built-in temperature sensor will pass the telemetry port to transfer and overlay to the OSD of FC,It can be programmed setting for temperature protection.
◆ With USB linker can be programmable throttle setting like support positive and negative,two-way mode,FPV 3D mode,motor speed,braking ,PWM frequency, inlet angle speed setting, onboard RGB LED for customize color, Beep etc.
◆ It use the self-adaption control system,can go automatic with the all kind of the motor in the market,at the mean time it support up to 500HZ PWM,oneshot 125,oneshot 42,Multishot and Dshot 150/300/600/1200.
◆With special optimize in multi-axis,the motor can launch smoother in a good throttle curve, fast response,great power, and highly support the multi-axis,fixed-wing and helicopter.
◆Signal wire is the silicone flat cable,it can connect with the DYS F4 FC directly,no need soldering.When it connect with the other brand FC,it will need to solder to the FC.
◆ MCU hardware,Driver circuit ,Mosfet will come with double voltage protection.
◆ To adopt the new process MOSFET of low internal resistance, will help increase resistance to flow.Also,the professional MOS driver chip makes the best efficiency.
◆ Mosfet is covered with aluminum sheet for cooling,which can bring more efficiency and stability.
◆With special process of 8 layer thicken PCB will lower resistance, small calorific value and bigger impact resistance current.Nice optimize layout of the components and parts makes a smaller size,lighter weight and easy to build.

F4 PRO V2 Betaflight Flight Control :

* Betaflight DYS F4 PRO firmware

* STM32F405 master with higher refresh rate and more function ports

* 5V 3A BEC output

* 9V 1.2A BEC output

* 3.3V 0.3A BEC output

* Compatible all split-type escs, connect with DYS 4-in-1 esc (F20A or F30A) with flexible flat cable

* Support BF setting software to flash and debug OSD

* Integrated current sensor to monitor the power consumption etc in real time

* Use remote control to view flight control parameter through OSD

* Support SAMRT AUDIO, adjust the VTX by OSD

* Comes with heat resistance damping ball to upgrade the stability and operation

* 3-6s lipo input, integrated PDB, max withstand current 160A

* Net weight 10.5g, exclude the cable

* The refresh rate of PID and gyro up to 8K

Data:

l Whole size: L 38mmX W 38mm, hole distance 20X20mm

l Six-layer PCB board and 3OZ copper to enhance the over-current and heat dissipation

l PDB board with reverse high voltage protection circuit

- MCU: STM32F405 GRT6

- IMU: MPU-6000

- OSD: AT7456E

- FLASH: 8M memory

- Current sensor: 0-200A

- Added S5,S6 motor control signal (support 6 axis feature once firmware upgraded)

- Integrated reverse high voltage protection circuit

- Integrated circuit protection to USB port

- 3.3V LDO to power on internal circuit

- 9V BEC: 1.2A

- 5V BEC: 3A/ one-way output to avoid external interference

- When use with 4-in-1 esc, plug in the battery to supply the flight control instead of BEC.

V+ V- : For esc power cable

S1-S6For GND of the corresponding esc signal cable

BOOT: BOOT button ( for firmware flash)

5V: 3A output, can connect with VTX, receiver, lens etc 5V power device at the same time

9V1.5A output, can connect with wide voltage device, such as 7-24V power VTX etc.

3.3VPower supply for DSMX etc 3.3V power device

GND: Negative

Vout: Video output for VTX image signal cable

Vin Video input for camera signal cable

LED: Programmable LED signal cable output

RX1: For sbus etc receiver

PPMFor PPM receiver signal pad

USart6 txSmart Audio set the VTX function( The VTX should support to use Smart Audio function)

BAT+/BAT-: Battery voltage

Buzz-Buzz+: Wiring for buzzer

Installation with DYS 4-in-1 esc (optional)

Connect DYS F20A or F30A with flexible flat cable, no need to solder

Note

* Please mount the mini F4 with the 4-in-1 esc as pic shows.

While using with 4-in-1 esc

* Please solder the battery power cable with esc power cable, do not connect with battery

* The current meter will be no use when use with 4-in-1 esc

* With voltage detection for battery

Caution

Please be attention to below attentions, otherwise your flight control will work improperly or damage.

* Please be always attention for the polarity. Double check before power on.

* Please keep the power off while plug or pull or any connection.

* Do not short the 5V or battery port, otherwise the flight control will be burnt

* After finished assemble, please check carefully and clean the residual solder splash to avoid short the components.

* Please mount the damping ball on the flight control (Equipped with accessory bag).

* If connect with 4-in-1 esc, please ensure the installation connect properly. Please do not force to plug or pull.

Prices for DYS F4 Pro V2 + Aria F45A 4 in 1 in stores

Deals found: 3 ()

F4 FCs

DYS F4 Pro V2 + Aria F45A 4 in 1

Prices for DYS F4 Pro V2 + Aria F45A 4 in 1 in stores

See also